We use cookies to offer you a better experience, personalize content, tailor advertising, provide social media features, and better understand the use of our services. To learn more or modify/prevent the use of cookies, see our Cookie Policy and Privacy Policy. I want to make a glue to adhere PVC to metal (for example Aluminium or stainless steel).This have to be partly air drying. What kind of resins do you recommend for adhesive? Thanks Slovak Academy of Sciences Metals have a high energy surfaces, and polymers (also polyvinychloridu, PVC) are low energy surfaces. For bonding polymers to metals it is necessary to increase the surface energy of the polymers using suitable modification methods, e.g. surface treatment of polymers with low-temperature plasma at atmospheric (barrier plasma) or reduced pressure (radio-frequency plasma) in an air environment. Surface treatment may also occur by using suitable primers, respectively adhesion promoters. Their application increases the polarity of the polymers and reduces the difference between the polarity of the metal and the polymer in the bonding and increases the strength of the glued joints. For bonding of aluminum (or stainless steel) substrate to polyvinychloride (PVC, hard) the pre-treatment of PVC to higher polarity is necessary. The surface of aluminum to hard PVC can be bonded using rubberized cyanoacrylate adhesive Loctite 480 with Loctite 770 primer (covering the PVC surface before gluing to drying). For bonding stainless steel, sand or corundum blasting is required prior to bonding, degreasing of stainless steel surface and then bonding. Ferdowsi University Of Mashhad Thank you very much Mr. Novak.It was so useful. another question: After rouphing the metal surface, metal gets smeared with glue.then PVC by 150 °C placed on metal. so is cyanoacrylate enough for that? Thanks for your kindness Slovak Academy of Sciences Dear Dr. Saiedeh Ghaffari, You can use for temperature 150 oC other suitable [costruction] adhesives, epoxy-based composite adhesives modified for higher temperature applications or polyurethane adhesives. Polyurethane adhesives have a nice resistance against water and epoxy-based adhesives have resistance against influence of mineral oils. For bonding of aluminum bar a fine abrasive paper [designed as 1000 or 1200] to remove aluminum oxide from the surface should be used.The abraded aluminum surface must be degreased e.g. with trichlorethylene or dichloromethane. For modification of PVC it is necessary to use primer, resp. an adhesion promoter, which is applied in a thin layer to the surface of the polymer and allowed to dry. This is followed by bonding the aluminum to the PVC, whereby the adhesive is carried on both surfaces of the substrates to be bonded. The bonded adhesive joint Al - PVC must be fixed until the adhesive, e.g.epoxy or polyurethane, cures. As an adhesion promoter, you can use a chlorinated polymer in an organic solvent solution or a primer based on an aqueous dispersion of the polymer that is environmentally friendly and less harmful to health, but this is a special category of solutions for plastic bonding. I can give you the necessary information about the appropriate primers. There is presently a growing interest for laminates made up of resins and metals and suitable for use as construction materials. The range of application of resin-metal laminates is extraordinarily wide. They may be utilized in all fields calling for metals, wood and coated pressings. Accurate molecular weight characterization of PVC is necessary before attempting to modify the properties of the polymer using additives and/or process the compound in some fashion. Commercial PVC resins are characterized by many different dilute solution viscosity methods. Manufacturers characterize their resins using K values, specific viscosity,... 流動試験機を用い,純PVCやそれに安定剤・滑剤を加えたコンパウンドの流動特性を測定した。一般にはPVCは顕著な降伏荷重を示し,これ以下では流動はきわめて困難である。荷重Pと押出速度Qとの関係は複雑であり,ポリエチレンやポリスチレンにくらべて加工性の困難なことがよくわかる。しかし主要部分ではlogQ=A十nlog(P-Pf)の型の式が大体成立し,特に滑剤を添加すると成立範囲は広くなる。ここにAとnは定数である。見掛け粘度の温度変化から流動の活性化エネルギーとして39kcalを得た。押出ダイスの長さの影響をしらべ,管長の補正係数を算出したが,この値もポリエチレン等にくらべるとはるかに大きかった。また重合度分配曲線の単一の極大をもつものと二つの極大をもつものとの流動性を比較し, 後者の方が流れ易い... Not finding the right answers on Google? Sign up today to join our network of over 15+ million scientific professionals.